Citrix 1Y0-A11 考试科目更新，下面是一些更新的题库，和大家一起分享。

1. Scenario: An administrator is planning the necessary configurations on a NetScaler system for an environment that requires the NetScaler system to advertise virtual IP addresses, directly connected routes and static routes on the upstream routers.
What must the administrator ensure is configured on the NetScaler system for this environment?
A. Static Routes
B. Link Load Balancing
C. Route Health Injection
D. Front-end Health Check
Answer: C

2. Which event would trigger a failover in a high availability pair?
A. The primary appliance reboots.
B. A forced synchronization event fails.
C. A monitored interface fails on the secondary node.
D. The default gateway does not return a heartbeat packet from the primary node.
Answer: A

3. A company is planning on implementing NetScaler systems in high availability pairs.
Which entry in the NS.CONF file of the secondary system needs to be unique from those of the primary system?
A. VMAC
B. VIP address
C. MIP address
D. NSIP address
Answer: D

4. A NetScaler system is running with high CPU usage frequently.
Which log can the administrator view to determine if the high CPU is being caused by the processes running in the user space?
A. syslog
B. nswlog
C. newnslog
D. nsconmsg
Answer: C

5. Scenario: An administrator installed a NetScaler system and configured the NSIP and MIP for the system. The NetScaler system will be used primarily for load balancing in this environment.
Which additional step must the administrator take to ensure that the NetScaler system can perform the necessary server load balancing in this environment?
A. Disable USIP mode on both nodes
B. Use the MIP as the NSIP for a high availability environment
C. Create VIPs for the front-end connections to the back-end servers
D. Enable USNIP mode for the front-end connections to the back-end servers
Answer: C

6. Scenario: A network administrator is deploying a NetScaler system in an environment with a single subnet using this IP information:
subnet: 192.168.10.32 netmask: 255.255.255.224 default gateway: 192.168.10.40 The administrator already set up the NSIP and MIP addresses using the command line interface.
Which command could the administrator use to complete this set up successfully?
A. add route 0.0.0.0 0.0.0.0 192.168.10.32
B. add route 0.0.0.0 0.0.0.0 192.168.10.40
C. add route 0.0.0.0 0.0.0.0 192.168.10.62
D. add route 192.168.10.0 255.255.255.224 192.168.10.32
E. add route 192.168.10.0 255.255.255.224 192.168.10.62
Answer: B

7. Scenario: An administrator is configuring a NetScaler system in one-armed mode. The NetScaler appliances are connected to the network through a switch and will be configured as a pair with high availability (HA) enabled.
Which two steps should the administrator take to succesfully configure HA in this environment? (Choose two.)
A. Ensure the NSIP is identical on both systems
B. Configure a unique nsroot password on each node of the HA pair
C. Disable all system interfaces except the one connected to the switch
D. Configure a Remote Procedural Call (RPC) node password on each node of the HA pair
Answer: CD

8. Which command can an administrator use to set up a NetScaler system to use SNIPs instead of MIPs for connections to local resources?
A. set ns ip snip -mip
B. set ns mode USNIP
C. add ns mode USNIP
D. enable ns mode USNIP
Answer: D

9. Scenario: An administrator is configuring the NetScaler-owned IP address for a network environment where the NetScaler IP, the mapped IP, and the back-end servers will be located on separate subnets. The administrator wants to create as few additional routes on devices, such as the servers, as possible while maintaining the communications between the NetScaler and the other devices.
Which two steps can the administrator take to achieve this? (Choose two.)
A. Enable USIP mode
B. Configure VIPs for the devices
C. Ensure USNIP mode is enabled
D. Make the MIP and the NSIP address the same
E. Configure SNIPs on the subnets of the devices
Answer: CE

10. An administrator is deploying a NetScaler system using the command line interface and plans to configure the MIP as 10.48.192.17.
Which command must the administrator use to correctly configure the MIP for this NetScaler system?
A. set ns config -ipaddress 10.48.192.17
B. add ns ip 10.48.192.17 255.255.255.0 -type mip
C. add ns config -ipaddress 10.48.192.17 -subnet mask 255.0.0.0
D. set ns ip -ipaddress 10.48.192.17 -netmask 255.255.255.0 -mip
Answer: B
相关科目更新：E20-097 , EX0-106 , EX0-107 和 SY0-201 认证
更多的更新科目，敬请访问Pass4side网站，了解最新的认证资讯，以最快的速度通过IT考试认证。